Search found 3986 matches

by kgschlosser
Thu Aug 16, 2018 2:32 pm
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

well this is what has me a little bit confused RuntimeError: libpng signaled error libpng is a linux thing. so why it is throwing an error on windows is beyond me. I made a change and removed the use of saving the data to a temp file and then loading that temp file into PIL.Image. so this may help I...
by kgschlosser
Thu Aug 16, 2018 2:21 pm
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

ok so good new is we got past the first problem. bad new is that error doesn't tell me a thing. LOL
by kgschlosser
Thu Aug 16, 2018 3:48 am
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

ok so I want you to replace the libs folder in the plugin directory with the one i have attached to this post. just go into the plugins folder and delete the libs folder. then uncompress this into the plugin folder.

see if the error still occurs.
by kgschlosser
Wed Aug 15, 2018 6:19 am
Forum: Show Off Your Automation Setup
Topic: My Home Theater build progress
Replies: 11
Views: 2841

Re: My Home Theater build progress

i believe i posted some photos of my speaker stands also. i built mine. no one made any that could hold 80 lbs 3 feet off the floor and 6" off the wall and have a 12" offset where it screwed to the wall from where the speaker was going to sit. all of this without any of the stand showing. and withou...
by kgschlosser
Wed Aug 15, 2018 6:14 am
Forum: Show Off Your Automation Setup
Topic: My Home Theater build progress
Replies: 11
Views: 2841

Re: My Home Theater build progress

ok so i am going to give you a really nice tip on running wires.. depending on where things are in your room and how much wire you have available to you depends o what you will need to do. if you can only make a line of sight run with the wire you will need to roll back your carpet. take a marker an...
by kgschlosser
Wed Aug 15, 2018 5:37 am
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

new version is up on the first post. please read the directions at the bottom.
by kgschlosser
Tue Aug 14, 2018 6:30 pm
Forum: General Support
Topic: HTTP Request / trim response
Replies: 5
Views: 87

Re: HTTP Request / trim response

that is the beauty of the way i went about it. it does not matter if it is prefixed with a 0 or not. once you turn it into an int/float it is going to remove the prefixed 0's The reason why they are probably not using a float or a decimal representation of the temperature is because if they use a UI...
by kgschlosser
Sun Aug 12, 2018 6:26 pm
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

well in the event you do not want to see the black bars. I have added the zooming features to the plugin zoom in = ctrl + numpad+ zoom out = ctrl + numpad- I am going to have to dink around with the HighDPI stuff in windows to see if there is anything I can do about it. It is going to take me a whil...
by kgschlosser
Sun Aug 12, 2018 4:40 am
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

OK i did some research on the black marks when running in what is called "High DPI Mode" and this is something that is not fully supported in wxPython 3.0. I can set wxPython into High DPI Mode but there is still a large portion of the wx Code that does not correctly work with it.. Specifically Size...
by kgschlosser
Sat Aug 11, 2018 11:10 pm
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

that is going o be an issue not with 4K but with wxPython and the high DPI. tho i do not understand how setting the DPI to a higher number enlarges anything on the screen. Dots Per Inch (DPI) as you know is the number of horizontal and the number of vertical dits that are drawn in a given inch of sp...
by kgschlosser
Sat Aug 11, 2018 8:32 am
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

@holdestmade Does that black bar also appear with other plugins??? I would test it with another plugin that has a decent amount of controls. and complex controls mind you. 50 buttons does not count!! LOL I need to know if it is perhaps a limitation of wxPython (the GUI control system in EG) for some...
by kgschlosser
Sat Aug 11, 2018 8:01 am
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

ok ladies I am not to far off from another release. this one is going to have the Set action repaired. I am also going to add in that visualization of the network. I feel that it is extremely important to have an optimized network and being able to see the connections is going to be a great help. Th...
by kgschlosser
Fri Aug 10, 2018 6:28 pm
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

I have fixed the issue with Set i still have to release it. I am also adding some new things as you can see. so when i am done with that the update will be posted. You did find the administrative control panel yes?? It is in the plugin config dialog. look at the tabs you should see Settings and then...
by kgschlosser
Fri Aug 10, 2018 6:26 pm
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

I found a couple more bugs.. well typos to be specific I am fixing them and I am also adding a pretty cool feature. it is going to show where your zwave network has bottlenecks. This is going to be a handy thing to let you know if you need to add a range extender to improve network performance. zwav...
by kgschlosser
Fri Aug 10, 2018 9:31 am
Forum: Plugin Support
Topic: Z-Wave
Replies: 41
Views: 362

Re: Z-Wave

i found out why it is doing that BTW. the Windows API is written wrong. It states that the following filenames are reserved CON, PRN, AUX, NUL COM1, COM2, COM3, COM4, COM5, COM6, COM7, COM8, COM9 LPT1, LPT2, LPT3, LPT4, LPT5, LPT6, LPT7, LPT8, LPT9 It does not state folder name. But anywho i changed...