Switch King Plugin

[woggy]

This plugin allows you to control yourTellstick through Switchkings REST API

Features:

• Device ON / OFF
• Device Fake ON / OFF (without sending a signal)
• Device Dim
• Device Fake Dim (without sending a signal)
• Device By Schedule
• Device Synchronize
• Device Get State
• Group ON / OFF
• Group By Schedule
• Group Synchronize
• Scenario Activate
• Set Datasource
• Set System Mode
• Device Get State (Get current state on a Device)

Events:

• Data Source Events
• Device Events
• Scenario Events
• Schedule Mode Events
• Debug Mode, Print all REST Events

You need to have Switchking Server Server - v3.0.0 or later and the REST service enabled on the server.
The server should also accept TCP on port 8800 in the firewall, if any.
This plugins original author is Martin Engstrom and can be found here eventghost-switchking-plugin
All credit goes to him.

Changelog

V0.0.8

• Added some basic error handeling
• Minor bugfixes

V0.0.9

• REST API Bugfix
• More error handeling

V0.1.0

• More REST API Bugfixes

[kalinkamaen]

Problems with switchking plugin.
Can some one help me?

[krambriw]

If I'm not completely wrong, I think I have seen this too and it was because SK server was not correctly started.
Try to restart all SK services and then try the plugin in EG again

[woggy]

Problems with switchking plugin.
Can some one help me?

Try the new version 0.0.8.
It should give a better hint on whats wrong but krambriw is probably right

[Gyld]

Hi!

I have something like this as well...
I have tried to get this to work the last days, but I only get error messages like this:

All the services for SK is running like thay should, and I have tried to restarted them but that dues not solve this problem...

Any other suggestions?

(Sorry for the screenshoot... it is in Swedish. I can make an other one in english if some one like to have it translated)

[Gyld]

Hi!
I experienced something similar when I try to start the Event Ghost with this pluguin.

As you can see in the screenshot below, I also get a lot of error messages. I have several times tried to restart the Switch King services and then restarted the Event Ghost, but without result.

Some info about my system:

Does anyone have any other suggestions on what this could be?

[woggy]

Is it the same error on V0.0.8?

[Gyld]

Is it the same error on V0.0.8?

I am using V0.0.8

[woggy]

Is it the same error on V0.0.8?

I am using V0.0.8

The error on line 395 is from 0.0.7

Have you tryed to restart the Client, it's sometimes needed when adding new data sources or devices

[Gyld]

Is it the same error on V0.0.8?

I am using V0.0.8

The error on line 395 is from 0.0.7

Have you tryed to restart the Client, it's sometimes needed when adding new data sources or devices

For me to be 100% sure I uninstalled Switcking from Event Ghost, closed Eventgost and deleted the Switshking folder from plugins-folder.
After that I downloaded 0.0.8 and above installed that in Eventghost.

But I still get this error message:

Pls help me... What am I missing?
Is there any other file that I should delete that is laying around in the system from the old 0.0.7 that is messing things up?

[woggy]

Ok, try V0.0.9

[Gyld]

Ok, try V0.0.9

Many thanks for the quick response!

I have installed the v0.0.9 and now it seams to receive information from my temp sensors in Switch King, but I still get some error messages:

Does you have any solution on that as well?

[Gyld]

Here is an other screenshot where the system has been running for some minutes.

[woggy]

Okey, try V0.1.0
The REST API is not consequent at the time being so it's a bit hard to extract the information. If you enable ONLY "Debug mode" the ID numbers should come in sequence and not skip any number.

[Gyld]

Okey, try V0.1.0
The REST API is not consequent at the time being so it's a bit hard to extract the information. If you enable ONLY "Debug mode" the ID numbers should come in sequence and not skip any number.

I really appreciate your efforts in trying to get this to work! Awesome nice!

Unfortunately I must announce that I still get lots of errormessages even with v0.1.0

If I understood you correctly, it was JUST debug you wished to be check?